1:通信電纜故障測試儀  電纜故障測試儀 通信電纜故障檢測儀 型號：ZYY1-TDR-368

 .產品簡介
ZYY1-TDR-368型回波測試儀是采用現代微電子研制成的科的電纜故障自動綜合測試產品。ZYY1-TDR-368具有脈沖反射和智能電橋兩種測試方法，適用于測量電力電纜、市話鉛皮電纜、塑電纜、用戶皮線的斷線、混線、地氣、緣不良、接觸不良等故障的位置。是縮短故障查找時間、提作效率、減輕線路維護人員勞動強度的得力具。線路查修人員也可以用其行線路程驗收和檢查電纜電氣性。
                     
二 .產品點
● 結合了脈沖反射測試法和智能電橋測試法，可以測試斷線、混線、緣不良等各種類型的故障。電橋法只適用于通信電纜。
● 具有自動測試能，只需按動次按鍵，故障點即可找到。
● 保留有手動測試能。
● 采用中文菜單，易于掌握和使用。
● 具有兆歐表和歐姆表能，能夠測試緣電阻和環路電阻。此項能質只使用與通信電纜
● 可以*保存10個測試波形，關機后不丟失，分替代打印機能。
● 采用自動增益和自動阻抗平衡，替代繁瑣的電位器調節。
● 液晶顯示屏具有背光能，即使在晚上也能行測試。
● 采用可充電鋰電池，智能充電，值守。
● 體積小，重量輕，便于攜帶。

三 .標
1． 脈沖反射測試法：
● zui大量程8km，可以根據電纜長度選擇適合的量程。
● 測試盲區：0m
● 測試度：
        量程小于2km時為1m
        量程大于2km時為8m
● 脈沖寬度：80ns-10μs自動調節
● 阻抗平衡自動調節
● 增益調節：自動和手動相結合
2． 智能電橋測試法（適用于通信電纜）：
● 能夠測試緣不良電阻zui大值：100МΩ
● 測試度：±1%×電纜長
● 能夠測試電纜zui大長度：9999m
● 可以分三段輸入，可以輸入線徑0.3mm-0.99mm
3．
● 充電時間約3個半小時
● 充滿后連續作時間5小時
● 體積：230×150×160
● 重量：2Kg

2:汽車尾氣檢測系統 汽車尾氣檢測儀 型號：NTP1-HPC508

NTP1-HPC-508 汽車排氣分析儀（ASM況法用）

    NTP1-HPC-508汽車排氣分析儀可應用于穩態況法（ASM法）和簡易瞬態況法（Vmas）的系統設備配套，是簡易況法行汽車檢測的用分析儀器。儀器采用口業檢測器，按照美BAR-97的有關要求行和制，滿足標GB18285-2005中穩態況法的測量規范和度要求，可測量CO、HC、CO2、O2、NO、λ及AFR、發動機轉速、油溫，備有多種標氣入口，自動反吹能，滿足北京地方標準及家有關標準的使用要求。也可廣泛應用于機動車排氣污染分析連續檢測、發動機排放分析研究等。

主要能與點:

★度、分辨率、本儀器滿足歐I-IV標準車輛的排放檢測。

★自動調零、自動清洗、自動溫度補償、壓力補償、。

★具備氣路泄漏檢查、量監控、HC殘留檢測、反吹清洗取樣管氣路。

★備有ASM法、雙怠速檢測和普通怠速檢測多種測量模式、發動機轉速、油溫等各項參數測量能。

★可車號輸入及2000組數據存儲、備查能、時鐘顯示。
★可選用壽命長、度的紅外（NDIR）NO分析平臺，反應速度比傳統電化學原理檢測器快三倍。

主要參數：

測量范圍     HC：0～10000×10^-6（ppm）vol   CO:0～10×10^-2(%)vol  

             CO₂:0～20×10^-2(%)vol          O₂:0～25×10^-2(%)vol      

             NO_x:0～5000×10^-6（ppm）vol

示值誤差

分辨率  HC：1×10^-6（ppm）vol   CO: 0.01×10^-2(%)vol   CO₂: 0.1×10^-2(%)vol

        O₂: 0.01×10^-2(%)vol    NO_x:1×10^-6（ppm）vol   λ:0.01

重復性  CO：0～7.00% ≤±0.02%或±2%讀數，        7.01～10.00% ≤±3%讀數

 CO2：0～10.00% ≤±0.1%或±2%讀數，       10.01～16.00% ≤±3%讀數

 HC：0～1400ppm ≤±3ppm或±2%讀數，       1401～2000ppm ≤±3%讀數

 O2：0～10.00% ≤±0.4%讀數，              10.01～25.00% ≤±1%讀數

 NO_x：≤±8ppm或±3%讀數。

注：以上誤差中滿足其中項要求即可。

HPC-508 auto exhaust analyzer(ASM)：

HPC-508 auto exhaust analyzer can be applied to steady-state condition method (ASM method) and simple transient conditions France (Vmas) system equipment package, is a simple method for vehicle inspection conditions dedicated analytical instruments. Equipment imported professional detector, according to the U.S. BAR-97 with the relevant requirements for the design and manufacture to meet the latest national standard GB18285-2005 in the steady-state condition method of measurement standards and accuracy requirements, measurable, CO, HC, CO2, O2, NO , λ, and AFR, engine speed, oil temperature, a wide range of standard gas entrance, automatic cleaning function, to meet the Beijing local standards and national standards relating to use requirements. Can also be widely used in motor vehicle exhaust pollution analysis of continuous testing, engine emission analysis studies.

Main Features:

◆High-precision, high resolution, the instrument to meet the European I-IV standard emissions testing of vehicles.
◆Auto-zero, automatic cleaning, automatic temperature compensation, pressure compensation.
◆Have the gas line leak inspection, traffic monitoring, HC residue testing, cleaning gas sampling tube cleaning path.
◆With ASM method, pairs of test and normal idle speed idle test a variety of measurement mode, engine speed, oil temperature, and other parameter measurement function.
◆License plate number can be entered and the 2000 set of data storage, reference function, clock display.
◆Can choose long life and high precision infrared (NDIR) NO analysis platform, the reaction rate than the traditional three times faster electrochemical detection principle.

Main technical parameters:

Test Scope：HC：0～10000×10^-6（ppm）vol  CO：0～10×10^-2(%)vol

CO₂：0～20×10^-2(%)vol   O₂：0～25×10^-2(%)vol   NO_x:0～5000×10^-6（ppm）vol

Shows the value error：

3:煙度計 型號：NTP1-HPC601

主要能點：
     體化結構；
      采用分式取樣、柴油機加速、減速和穩速時均可測量煙度；
      數據自動線性化處理，可顯示不透光度N、光吸收系數K和對應濾紙式煙度值SF；
      亮度數碼顯示；
      采用“空氣幕"保護光學系統免受污染；
      檢測室自動恒溫控制，可防冷凝而影響測試度； 
      附自動時間顯示,可選配轉速測量和油溫測量；
      出現故障自動診斷顯示所在單元；
      配內置打印機（或數字RS－232A接口或模擬接口）。
主要參數：

測量范圍              不透光度N:0～(相當煙度值0～10FSN) 

   光吸收系數K:0～16.06m^-1

示值誤差              ≤±2%(測量值)

穩定性                自動校零，量矩漂移≤±1%/4h

重復性                重復誤差≤±1%

分辨率                0.1%

輸出方式              數字直讀顯示，可附打印機打印煙濃度(暗度)zui大值，測試

                      時間、日期等?？筛浇涌谂c計算機聯網

測量煙度溫度          70℃(自動恒溫)，當溫度誤差≥±10%時，溫度及錯誤示

                      燈亮

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V 50Hz 消耗率150VA

外形尺寸（含支架）    160mm(深)×400mm(寬)×480mm() 

重量                  約8kg

Main Features:

◆Integrated Structural Design
◆Adopted a triage-type sampling technique, diesel engine acceleration, deceleration, and steady speed can be measured when the smoke
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K and the corresponding value of filter paper-type smoke SF
◆High-brightness digital display;
◆Use of "air curtain" technology to protect the optical system from pollution
◆Automatic detection of room temperature control, anti-condensation can affect the testing accuracy
◆Automatically attached to the time display, and optional speed measurement and oil temperature measurement
◆Show where the failure of automatic diagnosis unit;
◆Equipped with built-in printer (or digital RS-232A interface or analog interface)

Main technical parameters:

Test Scope：No light transmission N:：0～ (equivalent to smoke value 0 ~ 10FSN)

Light absorption coefficient K：0-16 .06 m^-1 
Shows the value error：≤ ± 2% (measured value)
Stability：Automatic zero, volume moments drift ≤ ± 1% / 4h
Repeatability：Repeat the error ≤ ± 1%
Resolution：0.1%
Output Mode：Digital direct-reading shows that smoke concentrations can be attached

printer (dark degrees) the maximum test time, date and so on. Can be

attached to interface with the computer network
Measurement of smoke temperature：70 ℃ (automatic constant temperature), when

the temperature error of ≥ ± 10%, the temperature and the error

indicator light
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz Power consumption 150VA
Dimensions (with stand)：160mm (depth) × 400mm (width) × 480mm (H)
Weight：About 8kg

4:自動濾紙式煙度計  濾紙式煙度計 煙度計 型號：NTP1-HPC701

主要能點：
自動濾紙式煙度計，用于柴油車自由加速狀態下排煙的煙度測量。自動成測量過程，自動顯示1、2、3次測量值及其平均值，亮度數碼管顯示，附時間顯示，出現故障自動診斷顯示所在單元，可配內置打印機（或數字RS－232A接口或模擬接口）

主要參數：

Main Features:

Automatic filter paper-type smoke meter for diesel vehicles free of tobacco smoke accelerate the state measurement. Auto-complete measurement of the whole process automatically 1,2,3 times measured values and their average, high-brightness LED display, with a time display, automatic fault diagnosis shows there where the unit can be equipped with built-in printer (or digital RS-232A interface or analog interface)

Main technical parameters:

Range：0 ~ 10FSN
Indication error：≤ ± 3%
Repeatability：Repeat error ≤ ± 2%
Stability：Zero drift ≤ ± 3%
Exhaust volume sampling system：300 ± 15ml
Tightness：≤ 15ml/min
Effective working diameter of filter paper：30.7mm
Pumping action time：1.4 ± 0.2s
Environmental conditions：Temperature 5 ~ 40 ℃, relative humidity ≤ 90%

Power ：AC220v ± 10% 50Hz Power consumption 150VA
Dimensions： 520mm (length) × 360mm (width) × 200mm (H)
Weight：about 30kg

5: 汽車排氣分析儀 排氣分析儀 型號：NTP1-HPC302

主要能點：
　　

   用于測量汽車排放廢氣中的HC、CO、NO_x氣體濃度，采用外，口關鍵零件組裝而成。具有亮度數碼顯示，自動校零，自動數據線性化處理，氣路阻塞時自動報警，故障時自動診斷所在單元，打印測試之日期、時間能，配內置打印機（或模擬輸出接口或RS－232A數字串行通信接口），可行自由怠速和雙怠速測量，具有操作方便，測量數據準確，作穩定可靠等點。

主要參數：

測量范圍              HC：0～10000×10^-6（ppm）vol

                      CO: 0～10   ×10^-2(%)vol

                      NO_x :0～4000 ×10^-6（ppm）vol

示值誤差              HC±12  ×10^-6（ppm）vol(對誤差)或±5%(相對誤差)

                      CO±0.06×10^-2(%)vol    (對誤差)或±5%(相對誤差)

                      NO_x ± 25×10^-6（ppm）vol(對誤差)或±4%(相對誤差)

重復性                重復誤差≤±2%

分辨率                HC：1×10^-6（ppm）vol

                      CO: 0.01×10^-2(%) vol

                      NO_x:1×10^-6（ppm）vol

穩定性                自動校零，量矩漂移≤±3%

預熱時間              8min（可預熱3min應急檢測）

響應時間              95%響應不大于10秒

輸出方式              數字直讀顯示，可附打印機打印氣體名稱，濃度zui大值，測

                      試時間、日期等?？筛浇涌谂c計算機聯網

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V 50Hz 或DC12V（選加電源逆變器）

                      消耗率50VA

外形尺寸              420mm(長)×310mm(寬)×170mm()

重量                  約9KG

Main Features:

Used to measure vehicle emissions of HC, CO, NOx gas concentration, using advanced foreign technology, import the key components assembled. With a high-brightness digital display, automatic zero, linear automatic data processing, auto-alarm when the gas line blocking, fault diagnosis where the unit automatically and print testing date, time functions, with built-in printer (or the analog output interface or RS -232A digital serial communication interface), can be freely idling and dual idling measure, with easy operation, accurate measurement data, work stable and reliable characteristics.

Main technical parameters:

Test Scope：HC：0～10000×10^-6（ppm）vol

CO：0～10×10^-2(%) vol

NOx：0～4000×10-6（ppm）volShows the value error：HC ± 12×10-6（ppm）vol (absolute error)or± 5% (relative error)

CO± 0.06×10^-2(%) vol   (absolute error)or± 5% (relative error)

NO_x±25×10^-6（ppm）vol  ( absolute error) or ±4%(relative error)
Stability：Automatic zero, volume moments drift ≤ ± 3%
Repeatability：Repeat error ≤ ± 2%
Resolution：HC：1×10^-6（ppm）vol

CO：0.01×10^-2(%) vol

NO_x：1×10^-6（ppm）vol
Response Time：95% of the response to no more than 10 seconds
Warm-up Time：8 min（May the preheating 3min urgent examination）

Output Mode：Digital direct-reading show that gases can be attached printer name, the

concentration maximum, average and minimum test time, date, etc.. Can be attached to interface with the computer network

Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz or DC12V (select plus power inverter) Power

consumption 50VA
Dimensions：420mm (length) × 310mm (width) × 170mm (H)
Weight：About 9kg

溫馨提示：以上產品資料和圖片都是按照順序相對應的